Hot Incubator

Smart incubator model CM120E, is a triple-walled incubator with special advantages. Advanced thermal controller, incomparable accuracy and unique technology of HCT are from the most important advantages of this device. The round corners of the inner chamber have given the unit such beauty and elegance and greatly help the user in cleaning the device and the special steel that is used in making the outer body is one of the most beautiful and durable (to withstand abrasion) stainless steels.

Design of this device is a masterpiece in the beauty and science of engineering. Advanced steps of production and quality raw materials have made this device one of the most unexceptionable products made domestically. This device is used in a variety of clinical, industrial, medical and research laboratories.

  • Stainless Steel body
  • Volume 120 liters

Model selection guide

Select according to product specifications
  • The heater element is embedded in protection stainless steel shield
    • Inner chamber and Heater element container made of stainless steel
    • Independent, adjustable safety thermostat with visual temperature alarm
    • External Case Coated with electrostatic powder paint
    • Adjustable front ventilation flat slide and rear exhaust Ǿ50 mm
    • Equipped with Error Alarm
    • 2 Chrome - plated racks for better uniformity
    • Triple-walled
    • Inner glass door

Utilizing the unique technology of HCT (Homogenize Chamber Technology)

  • Short warm up times
  • Uniform circulation even under full load
  • Temperature stability and reproducibility
  • High heating rate
  • Triple-walled
  • Quick drying

Outer body

  • Specially designed air exhaust port for maximum output of escaping fumes and gases from the rear.
  • Specially designed wire passing channel through the hinges to prevent damage to the controller interface wires
  • Very tight door closure with 2-point door latch.
  • Independent, adjustable safety thermostat with visual temperature alarm
  • Beautiful and ergonomic design

Microprocessor controller

  • Outage detection in time of operation and subsequent notification of the operator
  • 999-hour smart timer (permanently operable)
  • PID controller with an accuracy of 0.1 degree
  • Adjustable thermal ramp
  • PT 100 temperature sensor
  • Central troubleshooting system
  • Delay timer

Inner chamber

  • Easy loading and unloading of specimen material
  • Fully stainless steel.
  • Rack with tilt protection.
  • Easy cleaning.
  • Silicon tape around the door instead of magnet ones
  • Easy access to the element container for cleaning
  • Low heat dissipation due to 60 mm insulation.

Services and golden warranty

  • 10-years after sales service
  • 5-years element warranty
  • 1-year replacement warranty
  • 2-years warranty


Exterior dimensions CM120E
Plus door handle and connection (cm) 75
wall clearance, rear (cm) 10
Wall clearance, side (cm) 16
Exhaust duct (outer Ø cm) 5
Height (incl. feet) (cm) 67.5
Number of doors (ea.) 1
Weight (empty) (kg) 61
Width (cm) 82.5
Depth (cm) 68
Interior dimensions CM120E
Racks (number standard/max.) 2-(5)
Permitted total load (kg) 25
Load per rack (kg) 5
Interior volume (l) 120
Width (mm) 45.5
Height (mm) 45.5
Depth (mm) 59
Temperature data CM120E
Temperature range approx. 5 °C above
ambient temperature to (°C)
80
Temperature variations @ 37 °C ±0.1
Temperature variations @ 50 °C ±0.1
Display accuracy @37 °C ±0.1
Display accuracy @50 °C ±0.1
Uniformity CM120E
@37 °C(±k) ±0.2
@50 °C(±k) ±0.5
heating-up time (*) CM120E
heating -up time to 37 °C (min) 70
Recovery time after doors were open for 30 sec (*) CM120E
@ 37 °C (min) 5
@ 50 °C (min) 8
Electrical info CM120E
Frequency (HZ) 50
Voltage(V AC) 220
Current (A) 1.8
Power (W) 400

(* )To 98% of the set value

All technical data are specified for units with standard equipment at an ambient temperature of 25 °C and a line voltage fluctuation of ±10%

  • Installation of exhaust valves in custom number and diameter
  • Additional stainless steel rack
  • Custom made order is available
  • Metal-framed glass doors
  • Calibration certificate










Some of our clients